Beiträge von vassilist

Hello Unlimited,

The time in the system works perfectly. When the zenec device starts up after 1-2 minutes the time is set correctly. But the day/night skin is not set correctly. I mean that fistly is starts in day mode, after about 10 seconds become night, then after about 1 minute the time is set correctly, but the skin (and the brightness) doesn't change to day mode (when it is day time). I have to open the Navigation for the skin to change to day mode. Everything in Navi mode works perfectly. I mean that the transition from day to night and vice versa works perfectly automatically. In all the other views (Radio/Media/ Phone) the change of the day/night mode doesn't work. The settings are correct Navi and Auto.

I have this problem since 2014. I have sent E-Mails to Zenec support and talked to the phone to the dealer here in Greece. The Zenec support told me to contact the dealer and the dealer cannot actually help me. The solution could be to send the device (through the dealer) to Germany to Zenec. But it is a little bit difficult to remove the device from my car and get to all this trouble.

Well, I gave it a try, but the device says 'Not Required' and it cannot proceed in update. In summer time the change mode works when I start up the engine. But when it comes the sunset and I already drive the car it doesn't change automatically to night mode. In my case there must be something with the hardware, I think.

After the CAN update the 'Start / Stop' button lights out after 10 seconds.

Thank you Ocora. I'll try to do that and see if it will work.

I would like to say that this problem first occured to my Z-E3215 with a previous version than 0.7.0_03P3_141218. However I'll do the update again and see if it will work.

Hello guys,

I have, in my Z-E3215, the same issue with the one that ocora reported in post 1643. When I start up my car the zenec device starts in 'night mode'. In order the HMI to change to 'day mode' (when the time is day) I have to open the Navigation (by pressing the NAVI button). This is the only problem I have with my device. It was first introduced when one day the media had stuck and I performed manually reset through the button.

I performed the CAN Bus update. Will now the power management be better? Will this change stop getting our battery empty? Will the start / stop now work? In wintertime the engine does not stop when the car is stopped. Will that be fixed?

Please, I need also fix for the day/night transformation reported above.

Hello,

unlimited could you please post your Setup.ini file......

You have to export your settings to a usb stick.

Thanks

Sorry, it's Setup.ini and it is located under C9SL_Config directory. Here is the content of mine:

[Version]
ADP=ADP 4 V0.109
APP=APP_V 1.0.43_03P3_131026
Data=5775
Detail='01.39.10','Dec 06 2012','15:48:42',7165c1d5
DeviceID=Z_E3215
EBoot=EB2C9S10D_20121206
Firmware=HW07-SW01.39.10
Lib=5.6.2.9
MCU=MCU_V 0.6.7_03P3_131025
Manufacture=Parrot
ModuleName=FC6000N
NBoot=NB2CL000D_20100906
OS=WOS_V 3.32.0_BMW3_121126
RDSAFHandler=AF_HANDLER_V 2.8.6
RDSBasebandDecoder=RDS_BASEBAND_DECODER_V 0.0.0
RDSGroupDecoder=RDS_GROUP_DECODER_V 3.6.3
RDSLibLink=LIBLINK_V 2.1.5
UUID=1026501011300084
[CarConfigInfo]
ACInfo=1
OBCInfo=1
ParkRadar=4
Suspresion=1
TyrePressure=1
[General]
ACPopup=1
ALLFUN=1
ALTBtn=0
AutoDimmer=0
BrightnessSet=1
KeyColor=4
NaviDayNight=0
NaviGuidState=0
OPSBeep=1
ParkAssist=2
RadioField=2
TFT=4
UIControl=0
[Volume]
NaviVolume=1
NavigationMix=1
StartVolumeAdjust=5
TAVolume=1
VolumeStart=0
[BassFreq]
value=1
[MiddleFreq]
value=1
[TrebleFreq]
value=1
[ASP]
AuxinGain=6
DVBTGain=6
DVDGain=6
HDGain=6
SatGain=6
TunerGain=8
iPodGain=6
[Misc]
AntiSW=1
ParkingOverride=0
[Radio]
GroupIndex=2
[Video]
Brightness=10
[BassGain]
value=9
[user]
bass=9
treble=12
[TrebleGain]
value=12
[Subwoofer]
value=16

GPS time works fine.

I don't remember the folder, I 'll do it myself too and I'll post you the folder...

Thanks

unlimited could you please post your system.ini file in order to compare yours and mine?

Could it be that your file may have another one entry, that I don't have, controlling this feature.....

Well, I did it yesterday, but no luck, it didn't work.....
What I did:
- plugged off the negative pole of the battery for 30 minutes
- reset, through the button the zenec device

I had installed the latest firmware a few months before (main system and can interface), but I had not perform the battery disconnection step.

I have no other problem with the zenec device but this. Don't know what else to do to fix it. Not that it is that bad, but it would be nice if it worked too.
Thanks

Thank you unlimited for your answer, I'll try it..............

However, I'd like to tell you that I have communicated this to zenec and they said that this is how the device work. What can I say? The device did not work like this before. Don't they know how their device work?