ZENEC NAVICEIVER Z-E3215 anfang 2013 für BMW 3er e90/91/92

Kann dazu leider nichts sagen, da ich die Freisprecheinrichtung nicht nutze, aber die Bedienungsanleitung hast du sicher schon nach Informationen durchsucht!?

Zitat von aw812

selbst schuld wennse nen Eierphone benutzt.

Ich habe eigentlich nur 2 Fehler gemacht:
1. Leider ein Fahrzeug ohne Navi gekauft.
2. Mich auf das Zenec bzw. auf ACR eingelassen!

Also mein iPhone 6 und das 6s meines Kumpels lassen sich beide ohne Probleme koppeln und funktionieren, inkl Musik Streaming

Gesendet von iPhone mit Tapatalk

Hello guys,

I have, in my Z-E3215, the same issue with the one that ocora reported in post 1643. When I start up my car the zenec device starts in 'night mode'. In order the HMI to change to 'day mode' (when the time is day) I have to open the Navigation (by pressing the NAVI button). This is the only problem I have with my device. It was first introduced when one day the media had stuck and I performed manually reset through the button.

I performed the CAN Bus update. Will now the power management be better? Will this change stop getting our battery empty? Will the start / stop now work? In wintertime the engine does not stop when the car is stopped. Will that be fixed?

Please, I need also fix for the day/night transformation reported above.

Hello vassilist,

I have updated the mains system software for the device again ( Current version: MCU: 0.7.0_03P3_141218 ). Apparently the device has something forgotten ... Now it works again. The navigation software starts in the background and when the time is received via satellite, the mode changes.
After the CanBusUpdate the voltage switches off after approx. 10-15 seconds. You can see this well with the StartButton lighting.
In my case, the start-stop control is permanently switched off, so I don't know if something has changed.
Best regards...

Thank you Ocora. I'll try to do that and see if it will work.

I would like to say that this problem first occured to my Z-E3215 with a previous version than 0.7.0_03P3_141218. However I'll do the update again and see if it will work.

Well, I gave it a try, but the device says 'Not Required' and it cannot proceed in update. In summer time the change mode works when I start up the engine. But when it comes the sunset and I already drive the car it doesn't change automatically to night mode. In my case there must be something with the hardware, I think.

After the CAN update the 'Start / Stop' button lights out after 10 seconds.

Hallo Vassilist,

Did you ckecked the Zenec Time? Only with running GPS you get the right time.
If the time is not working correctly, the Zenec don't switch correctly.

When the System say "not Required", you don't Need a update.

Hello Unlimited,

The time in the system works perfectly. When the zenec device starts up after 1-2 minutes the time is set correctly. But the day/night skin is not set correctly. I mean that fistly is starts in day mode, after about 10 seconds become night, then after about 1 minute the time is set correctly, but the skin (and the brightness) doesn't change to day mode (when it is day time). I have to open the Navigation for the skin to change to day mode. Everything in Navi mode works perfectly. I mean that the transition from day to night and vice versa works perfectly automatically. In all the other views (Radio/Media/ Phone) the change of the day/night mode doesn't work. The settings are correct Navi and Auto.

I have this problem since 2014. I have sent E-Mails to Zenec support and talked to the phone to the dealer here in Greece. The Zenec support told me to contact the dealer and the dealer cannot actually help me. The solution could be to send the device (through the dealer) to Germany to Zenec. But it is a little bit difficult to remove the device from my car and get to all this trouble.